DirectOut PRODIGY.MP - Changelog 21-08-2024 ************************ Build 22b (20.8.2024) Bugfixes - Mirror mode: crash due to missing dependencies <- fixed ************************ Build 22 (5.8.2024) Features - USB.IO support added - FPGA: MADI RX improved - AES SRC lock/mute improved - improved information in support archive - LLDP - HOME: support multiple NATS Changes - improvements to internal watchdog - improved TCP/IP connection handling to avoid potential unavailability of the device Bugfixes - automator: issue matching OSC integer values <- fixed - FPGA: MADI#2 FastSRC Sample Rate Factor fixed - snmp: small bugfixes (NOTE: a new MIB file is required to use the updated version of the snmp service!) - HOME: service did not automatically start after reboot <- fixed ************************ Build 21 (19.12.2023) Features - Support for MADI2.BNC.SRC.IO Changes - AN8.O 2.0 - use fast Roll-off filter to avoid frequency issues above 18kHz (latency ~30 samples) Bugfixes - Net mask CID translation did not work properly - Stereo MatMix source levels were reset after power-cycle <- fixed - replaced wrong automator binary - front panel: improved behaviour of snapshot list ************************ Build 20 (17.10.2023) cored v2.7.1 FPGA v1.3 Build 69 Features - Link Local Address support if DHCP is not answering (zeroConf) - AES Output Dark - MIDI Tunnel for SG.IO (available in MIDI Matrix) - automator: link faders between devices - support for MADI2.BNC.SRC.IO - HOME support prepared Changes - FPGA: User Bit transparency also for NET slots with inactive AM824 setting - cored: increased number of possible connections - cored: improved log output - automix: pickoff point for fader switchable - improved stability of firmware updates for NET modules with SRC Bugfixes - FPGA: MTC 30fps - FPGA: MADI Slot 2 Sample rate factor information fixed ************************ Build 19 (25.05.2023) Features MADI2.SFP.IO support SNMP support Changes FPGA/cored: improved configuration for modules with ESS ADC converters autoupdated: improved stability of NET.BASE.SRC module firmware updates Bugfixes FPGA: MADI Mode Legacy/Highspeed swap corrected ************************ Build 18 (19.12.2022) Features Front Panel: Display Timeout and Brightness control Input Slot Labels Recall Snapshot 1/2 with GPI 1/2 (support for HCONTROL.8 via globcon/GLUE) Bugfixes FPGA: improved FastSRC FPGA: BLDS detection for 96k and 192k frame mode Ember+: fix for crash after many connection attempts Triggers would trigger always on device startup Gateway Information Fix for bit transparency mode in combination with ESS ADC modules improved configuration of ESS DAC modules to prevent unwanted muting ************************ Build 17 (2022-08-17) Crossfade for Groups Solo Bus Reset device without removing snapshots Reduced delay for ESS DA converters Crossfade for Groups in Ember+ service HOME button pressed for 30 seconds also restarts web server Automator (Settings/Licenses) ************************ Build 16 (2022-05-18) Upward/Downward compressor Gate SoftGate improved snapshot load behavior in config mode: automatic MUTE ALL is applied on recall WCK Out can be fixed to 1FS or Follow FS (Follow FS was previous behavior) MADI High Speed mode for 4FS (switchable) MADI Output Dark EARS with Disaster Recovery Input Mutes Ember+ with Levelmeter, MatMix, Flex Channel fader Support display and configuration of RAV.IO IP addresses added dynamic measurement of power consumption to allow usage of more than 6 MIC8.HD modules improved warning messages for PSU failure and power over-consumption ************************ Build 15 (2021-12-22) New Features support for analog I/O modules Rev 2.0 Bugfixes Hush wizzard value was not applied after reboot <- fixed ************************ Build 14 NOTE: This release requires globcon version 1.8.0. Build 12 needs to be installed first, if the device shall be updated from an earlier version (< build 12). New Features AutoMix TruePeak Metering for Loudness Meters MirrorMode 6 IIR Filters per IIR plugin User definable slot labels Changes Confirmation dialog on front panel for Mutes to avoid unwanted activation Confirmation dialog on snapshot page if snapshots are loaded in CONFIG mode Improved support archive information Bugfixes fixed issue with blocked License Manager Ember+: improved gain value representation ************************ Build 13 NOTE: This release requires globcon version 1.7.0 and Build 12 being installed first. NOTE: globcon version 1.7.0 needs to be downloaded from www.globcon.pro - it is not updated automatically from an earlier version installed. Features Custom filters Silence detection for Input Managers Automatic Bypass for FastSRC(TM) Loudness Metering (license option) ************************ Build 12 NOTE: This release requires globcon version 1.6.0 Features Front panel: signal present indicator in levelmeters aligned with globcon levelmeters Front panel: license information page with info about license state on the device Remote Control: Ember+ service with support of DSP and Generator routing, flex channel gain (faders), mute and phase Remote Control: OSC service Fixes Front panel: levelmeter flickering with static signals (e.g. sine wave) <- fixed Front panel: graphical module label wrap-around for certain module types <- fixed ************************ Build 11 NOTE: This release requires globcon version 1.5.0 Features Snapshots can be stored in the device and recalled stand-alone from the front panel "Configuration" and "Show" Mode Ember+ OSC Changes Improved MADI receiver Improved file handling for configuration data ************************ Build 10 NOTE: This release requires globcon version 1.4.0 Features Channel Link GROUPS: Flex Channels, MatMix Masters, Sum Bus Masters and Hardware Outputs can be assigned to up to 16 groups basic MIDI-over-MADI control support (Gains, P48, PAD -> use PRODIGY MIDI PlugIn in globcon) improved Fan speed measurement improved JSON parsing and creation Bugfixes improved DA Mute during power-on Critical: AoIP modules could be set and held in reset state after several weeks without reboot <- fixed Dynamics: Stereo link issue fixed Dynamics: Gain Reduction issue fixed minor bugfixes and improvements for reset to default values and JSON commands FrontPanel: Output Levelmeters did not work <- fixed FrontPanel: Phones Mute Button was not updated correctly in all cases <- fixed ************************ Build 9 (Release) NOTE: This release requires globcon version 1.3.0 Features Fast SRCs (bidirectional low latency asynchronous SRC) for MADI and NET I/Os 32 IIR Filters offering the combination of two filters selectable from All Pass, Low/Hi Pass, Low/Hi Shelf, Peak, Notch, Band Pass, Gain, RIIA Production/Playback Enhanced Dynamics with Mono/Stereo Link, Side Chain and Parallel Compression Added 32 Input Managers, with Signal Lock and selectable Level Coherence detection, selectable STEREO Link behavior, Sources auto level trim tool MIDI-Matrix (incl. support for MIDI-over-MADI tunneling) LTC to MTC converter Sine wave, Pink noise and white noise generators Enhanced Automatic Redundancy Switching (EARS) for NET and MADI I/Os Levelmeter speed configuration Bugfixes Lock state not preserved on page reload via Browser <- fixed Bit transparency for ST2110-31 and AES I/Os did not work properly <- fixed improved globcon bridge startup behaviour ************************ Build 8 (Release) NOTE: This release requires globcon version 1.2.1 Features Compressor/Dynamics added transparent mode for MADI and NET I/Os for ST2110-31 support SFP port support for Management network interface added Fan control with setting for temperature threshold and silent mode Front panel: Locking function with PIN entry and auto lock Front panel: optional home view with big LTC display (tap on LTC to activate) IMPROVEMENT: Update now preserves network interface configuration IMPROVEMENT: Many internal improvements around Flex Channel handling Bugfixes BUGFIX: clock source changes were not always displayed correctly on front panel BUGFIX: MUTE ALL button was not displayed as active if the MUTE ALL state was left by tapping on one of the MUTE groups instead of the MUTE ALL button IMPROVEMENT/BUGFIX: PAD initialisation during boot (MIC8.x modules)